Point Pod Connect closed flush in a marble island, with only a slim silver ring showing

Guide · Point Pod · USA

The Point Pod: How It Works, Models and Installation

A motorized pop-up outlet that hides under a disc of your own countertop. In the US it’s Point Pod Connect: how it works, which model to pick and how it’s installed.

By Seb Aroney, founder of Modern Power Solutions · Updated November 2026

Free shipping across the USAShips in 24 hoursUp to 4-year warranty1,800+ reviews

Quick answers

?What is the Point Pod?A motorized pop-up outlet whose top is a disc of your own countertop. Closed, only a slim ring shows; press the top and it rises 6 11/16″ with two outlets and USB charging. In the US it’s sold as Point Pod Connect.
?How is a Point Pod installed?In a 4″ hole, held from below. A collet is siliconed into the hole, a mounting flange is fixed underneath, and the unit drops in and clips to it. It plugs into a GFCI-protected outlet in the cabinet. The steps.
?What does it need?A 4″ hole and 19″ clear below, measured from the top of a countertop at least ½″ thick, with a GFCI-protected outlet within reach of its 6 ft cord.
?Which model should I get?Silver or black, with 15W or 65W USB. The 15W PPCV815 (silver) and PPCV815B (black) have two USB-C ports and a USB-A; the 65W models have two USB-C PD ports.
?Is it allowed in a kitchen countertop?It’s ETL listed to UL 962A and marked “suitable for installation in a kitchen countertop surface”. On an inspected build, show your inspector the listing first; we’ll send it.

How it works

A pop-up outlet that disappears into the countertop

Press to raisePress the top and let go: a motor raises it 6 11/16″, with two tamper-resistant outlets and USB charging. Unplug everything and press again to lower it.
Closes flushThe top cup holds a 3.66″ disc of your countertop, so when it’s closed only a slim ring and your stone show.
Plugs in belowA 6 ft cord runs to a GFCI-protected outlet inside the cabinet, so the unit itself needs no hardwiring.
Stays removableA mounting flange and fastening clip hold it from below. It’s never glued in, so it can always come out from under the countertop.
Silver Point Pod Connect raised in a marble showroom island, with two outlets and USB ports
Raised: two outlets and USB
Point Pod Connect raised in the middle of a marble showroom island
Mid-island in a showroom kitchen
Silver Point Pod Connect raised on a white counter beside a dining table
Beside the dining table
Silver Point Pod Connect raised on a light stone kitchen counter
On a light stone counter
Black Point Pod Connect raised on a dark stone kitchen island
In black, on dark stone

Point Pod is designed and engineered in Australia by Point Pod, and its countertop-insert design won a Good Design Award in 2019. It has been sold in the US as Point Pod Connect since 2022.

Models

Point Pod Connect: silver or black

Two colors, each with 15W or 65W USB. Every model takes the same 4″ hole and the same disc of countertop.

15W or 65W USB?

15W: PPCV815 and PPCV815BTwo USB-C ports and one USB-A port, sharing 15W (5 V 3 A).
65W: PPCV815PD and PPCV815PDBTwo USB-C PD 3.0 ports and no USB-A: up to 65W from one port, or 30W each when both are in use.

Everything else is the same on all four: the two outlets, the size and the installation. Model numbers, sizes and manuals.

Searching for the Point Pod Multi or Compact? Those are the Australian models, with Australian power points, and they aren’t sold in the US.

Installing it

How a Point Pod is installed

Have a professional countertop installer cut the hole and fit it. The six steps from the install manual:

1

Check the space. The countertop must be at least ½″ thick, with 19″ clear below (measured from the top surface) and 6 5/16″ across for the flange. Keep drawers and pipes clear, and have a GFCI-protected outlet within 6 ft.

2

Make the insert. Cut a 3.66″ (93 mm) disc of your countertop, up to 1 3/16″ thick, and test-fit it in the top cup. Our 4″ hole saw keeps the core from the hole whole for this.

3

Cut the hole. A clean, chip-free 4″ hole, using the template in the manual. Stone and quartz need a diamond core bit with water cooling, or a water jet.

4

Fit the collet and flange. Silicone the outer collet into the hole, flush with the top. Underneath, fix the mounting flange around it: two-part epoxy on stone, screws on timber.

5

Lower the unit in. Feed it down through the collet until the top sits flush, then tighten the fastening clip onto the flange. Never glue the unit: it must stay removable.

6

Glue in the insert and test. Silicone the disc into the cup, lining up the pattern. Once it’s set, plug in and allow up to a minute to start: the first press moves it down, the next raises it.

Specs

Point Pod Connect at a glance

Hole4″ (102 mm)Cut clean and chip-free
Countertop½″ or thickerNo maximum
Clear below19″ (483 mm)Measured from the top of the countertop
Flange6 5/16″ across160 mm, fixed under the countertop
Stone insert3.66″ (93 mm)Up to 1 3/16″ (30 mm) thick
Raised6 11/16″ (170 mm)Above the countertop
Outlets2 × 15 ATamper-resistant, 1,875 W in total
USB15W or 65WTwo USB-C and USB-A, or two USB-C PD
Cord6 ft (1.8 m)To a GFCI-protected outlet
Body3 7/8″ across16.14″ long when closed
ListingETL listedUL 962A and CSA C22.2 No. 308
Warranty24 monthsExtendable to up to four years

From the install manual. Full dimensions, both manuals and the model numbers are in the PPCV815 and PPCV815B guide.

Kitchen countertops

Is it allowed in a kitchen countertop?

Point Pod Connect is ETL listed to UL 962A and marked “suitable for installation in a kitchen countertop surface” after Intertek’s countertop spill test. It plugs into a GFCI receptacle under the counter, and it’s installed in kitchen islands every day.

UL groups plug-in units with furniture power, though, so on an inspected build show your inspector the listing before the countertop is cut; email us and we’ll send it. If hardwiring is required, Hubbell’s countertop receptacles (UL 498) are the alternative.

Kitchen island outlet code · Compare the listed pop-ups

Everyday use

Living with a Point Pod

Starting upAfter plugging in, allow up to a minute for it to start. The first press moves it down; press and release again to raise it.
Lowering itRemove every plug, clear the top, then press and release. If something blocks it while it closes, it reverses. Never force it down.
Spills and crumbsLower it when you’re not using it and wipe up spills straight away. Crumbs that get in usually drop through the weep holes in the flange, so vacuum the cabinet below now and then.
CleaningWipe the ring and outlets with a soft, dry or slightly damp cloth, and clean the insert as you would the rest of your countertop.
Service and swapsIt’s held by the fastening clip and never glued, so it can come out from under the countertop for service or a swap.
Warranty24 months, parts and labor. Eligible purchases can be extended to up to four years; conditions apply.

Questions

Point Pod FAQs

What is a Point Pod?

A motorized pop-up outlet designed and engineered in Australia by Point Pod. Its top holds a disc of your own countertop, so when it’s closed only a slim ring shows. In the US it’s sold as Point Pod Connect.

How do you install a Point Pod?

Cut a 4″ hole, silicone the outer collet into it and fix the mounting flange underneath. Then lower the unit in, tighten its fastening clip, glue a disc of your countertop into the top and plug it into a GFCI-protected outlet below. Have a professional countertop installer cut the hole.

What size hole does a Point Pod need?

4″ (102 mm), cut clean and chip-free. Underneath, allow 6 5/16″ (160 mm) across for the mounting flange and 19″ (483 mm) of clear depth, measured from the top of the countertop.

What is the Point Pod mounting flange?

The round bracket fixed under the countertop around the hole, with two-part epoxy on stone or screws on timber. The unit has no lip on top, so the flange and its fastening clip are what hold it in place.

Can it go in stone on a plywood sub top?

Yes. The mounting flange can be screwed and glued to the plywood; it’s a common setup. If the plywood can easily be cut away around the hole before the stone goes on, epoxying the flange straight to the stone is a little better.

Is the Point Pod spring-loaded?

No. It’s motorized: the built-in motor raises and lowers it when you press and release the top.

Do I need an electrician?

Not for the unit: it plugs into a GFCI-protected outlet under the countertop with its 6 ft cord. If there’s no outlet there, a licensed electrician needs to add one. Don’t use an extension cord.

Is there a Point Pod Multi or Compact in the US?

No. The Multi, Compact and Boardroom are the Australian models, with Australian power points. In the US it’s Point Pod Connect, with two US outlets and USB.

Is Point Pod Connect approved for kitchen countertops?

It’s ETL listed to UL 962A and marked “suitable for installation in a kitchen countertop surface” after Intertek’s countertop spill test. It plugs into a GFCI receptacle below the counter. On an inspected build, show your inspector the listing first; we can send it.

How long is the warranty?

24 months, parts and labor. Eligible purchases can be extended to up to four years; conditions apply.

Planning a Point Pod?

Point Pod Connect comes in silver or black, with 15W or 65W USB, and ships free across the USA. Fabricators and builders can order at trade prices.

Point Pod Connect raised in a stone countertop, with a disc of stone in its top
Back to blog
Seb Aroney, founder of Modern Power Solutions

About the author

Seb Aroney

Founder and Director, Modern Power Solutions

Seb has been developing pop-up outlets since 2013, and they're all Modern Power Solutions does: one specialist range for kitchens, islands and offices, sold across Australia, the US and the UK, with support and warranty handled by our own team.